W202 Mercedes
+ 1.2. General information
+ 2. Maintenance
+ 3. Engines
+ 4. Greasing system
- 5. Cooling system
- 5.2. Cooling liquid
5.2.2. Diesel engine
5.2.3. Cars with the conditioner
5.3. Antifreeze for a radiator
5.4. A temperature regulator cooling liquids (thermostat)
5.5. Check of system of cooling
5.6. Hydraulic coupling of the fan
5.7. Pump of system of liquid cooling
5.8. Radiator
5.9. Fan casing
5.10. Diagnostics of malfunctions of system of cooling
5.11. Diagnostics of malfunctions of system of indication of level of liquid
5.12. Engine overheat
+ 6. Heating, ventilation
+ 7. Ignition system
+ 8. Fuel system
+ 9. Transmission
+ 10. Running gear
+ 11. Steering
+ 12. Brake system
+ 13. Body
+ 14. Electric equipment
+ 14.2. Electroschemes
|
1. Compensatory tank
1а. A silicate stock (preventing aluminum corrosion)
2. A radiator with a horizontal stream of cooling liquid
3. A regulator cooling liquids (thermostat)
4. Water pump системыв liquid cooling
6. Heat exchanger of system of heating |
7. Ventilating (blowing-off) line
А31. Block of forcing of system of heating
А31у1. Double клапаг at the left
А31у2. Double клапаг on the right
M.Dvigatel
S. Capacity for обмыва glasses (warmed-up cooling liquid) |
| PERFORMANCE ORDER |
| 1. Remove the bottom cover of a motor compartment. |
|
2. Put on a hose the drain union of a radiator. In drawing – the engine in volume of 2,0 l. |
|
3. Put on a hose with internal diameter of 12 mm the drain union of a radiator. In drawing – the engine in volume of 2,5 l. |
| 4. Establish under a radiator a pure reception vessel, enter into it a hose and open a carving stopper of a drain opening. |
|
Plums
| PERFORMANCE ORDER |
|
1. Engine in volume of 2,0 l: put under the engine a pure vessel and turn out a carving stopper (12) drain openings on the block of cylinders of the engine. |
|
2. Engines in volume of 2,2/2,5 l: put on a hose with internal diameter of 14 mm a carving stopper (4) drain openings on the block of cylinders of the engine (shooter). |
| 3. Substitute under the engine a pure reception vessel, enter into it a hose and only weaken a carving stopper (4) drain openings, without unscrewing it. |
| 4. Completely lower cooling liquid. |
| 5. Tighten a carving stopper of a drain opening on the block of cylinders of the engine with the moment of 30 N of m. |
| 6. Twist with the moment of 1,5-2,0 N of m (manually) a carving stopper of a drain opening on a radiator. |
| 7. If it is got, remove a drain hose. |
| 8. Establish the bottom cover of a motor compartment. |
|
Gulf
| PERFORMANCE ORDER |
| 1. Check the content of antifreeze in cooling liquid. |
|
2. Fill cooling liquid through a bulk branch pipe of a compensatory tank (2) to a mark (shooter). At the vehicles having a black top part of a tank, prior to the beginning of a black part. |
Prevention
|
|
That cooling liquid quickly got from a compensatory tank to a radiator, and, respectively, in the engine, it is possible for filling with cooling liquid to squeeze out down a bulk hose. |
|
| 3. Connect to the storage battery a weight wire. |
4. Leave the engine to get warm until the regulator of temperature of cooling liquid (temperature about 100 ° by C) will be opened. Thus establish on full capacity heating and pushes press an accelerator pedal.
Prevention
At temperature of cooling liquid 60-70 ° C close a compensatory tank.
|
| 5. Check tightness of system of cooling – accessions of hoses, and also carving jams of drain openings. |
| 6. Expose time on hours. |
| 7. Enter an anticreeping code of radio. |
|
|
|
