S-class W202 Mercedes

1993-2000 of release

Repair and car operation

W202 Mercedes
+ 1.2. General information
+ 2. Maintenance
+ 3. Engines
+ 4. Greasing system
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. Ignition system
- 8. Fuel system
   + 8.1.1. Introduction
   - 8.2. System of injection of petrol engines
      8.2.1.1. Principle of work of PMS
      8.2.1.2. Principle of work of HFM
      8.2.2. Self-diagnosing of a condition of system of ignition and fuel injection
      8.2.3. Air flowmeter
      8.2.4. A temperature-sensitive element of cooling liquid
      8.2.5. The sensor of soaked-up air
      8.2.6. System of vacuum pipelines
      8.2.7. The fuel distributor with klapanny nozzles
      8.2.8. Klapannye of a nozzle
      8.2.9. Oxygen sensor (lambda probe)
      8.2.10. Diagnostics of malfunctions of system of injection of gasoline
      8.2.11. That it is necessary to know to the owner of the car with the injector engine
      8.2.12. Turbo doctor
   + 8.3. System of injection and food of diesel engines
   + 8.4. System of production of exhaust gases
+ 9. Transmission
+ 10. Running gear
+ 11. Steering
+ 12. Brake system
+ 13. Body
+ 14. Electric equipment
+ 14.2. Electroschemes

8.2.7. The fuel distributor with klapanny nozzles

GENERAL INFORMATION

Removal

Prevention

Provide good aeration of a workplace! Pairs of fuel are poisonous, avoid application of open fire because of danger of emergence of a fire!

PERFORMANCE ORDER

1. Disconnect from the plug of the storage battery a weight wire (–).

Prevention

The anticreeping code of radio is thus erased.

2. Reduce pressure паров fuels, for this purpose quickly open a cover of a bulk mouth of a fuel tank.

3. Remove a cross-section pipe of the air filter.

4. Remove a hose (1) for air removal from a case.

5. Remove a hose (40/11) being under depression.

6. Remove from the coil of ignition of a wire of a high voltage and disconnect them from spring clips on the fastening device.

7. Unscrew bolts (17/4) of clips топливопровода (17/5). Pay attention to that nuts (17/6) did not drop out.

8. Turn off submitting (17/2) and drain (17/3) топливопроводы. For this purpose weaken a cap nut and a hollow bolt (17/7).

Prevention

Before separation топливопроводов lay thick rags over connections to catch the remains of the fuel which are thrown out by probably remained residual pressure.

9. Remove shtekkerny sockets of klapanny nozzles (arrow).

10. Unscrew bolts (17/1) and remove rasporny plugs (17/8).

11. Carefully extend from the inlet gas pipeline the fuel distributor (17) together with klapanny nozzles.

Installation

PERFORMANCE ORDER

1. Insert the fuel distributor with new sealing rings of round section.

2. Insert rasporny plugs and screw the fuel distributor.

3. Pull the shtekkerny socket for klapanny nozzles.

4. Screw топливопроводы with new sealing rings.

5. Fix the drain pipeline on the fuel distributor by means of clips.

6. Get wires of a high voltage on coils of ignition and fix them in spring clips on the fastening device.

7. Get a hose for air removal from a case so that shooters on a hose and a rubber flange stood opposite to each other.

8. Establish a cross-section pipe of the air filter.

9. Attach to the plug of the storage battery a weight wire (–).

10. Establish time on hours.

11. Enter an anticreeping code of radio.

12. Start the engine and check tightness of junctions топливопроводов.