S-class W202 Mercedes

1993-2000 of release

Repair and car operation

W202 Mercedes
+ 1.2. General information
+ 2. Maintenance
+ 3. Engines
+ 4. Greasing system
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. Ignition system
+ 8. Fuel system
+ 9. Transmission
+ 10. Running gear
+ 11. Steering
+ 12. Brake system
+ 13. Body
- 14. Electric equipment
   14.1.2. Measuring devices
   14.1.3. Equipment of measurements
   14.1.4. Electric equipment checks
   14.1.5. Sound signal
   14.1.6. Replacements of safety locks
   + 14.1.7. Storage battery
   + 14.1.8. Generator
   + 14.1.9. Starter
   14.1.10. Traction relay
   + 14.1.11. Lighting system
   14.1.12. Devices
   14.1.13. Dashboard
   14.1.14. Filament lamps on the dashboard
   14.1.15. Light switch
   14.1.16. Radio receiver
   + 14.1.17. Aerial
   14.1.18. Loudspeakers
   + 14.1.19. Rubber brushes of screen wipers
   14.1.20. Jets of a stekloomyvatel
   14.1.21. Washing nozzles of headlights
   14.1.22. Screen wiper and its engine
   14.1.23. Protect the car
   14.1.24. Anticreeping "immunodeficiency"
   14.1.25. Why headlights grow dull
   14.1.26. "Galogenki"
+ 14.2. Electroschemes

b47c026d b47c026d

14.1.14. Filament lamps on the dashboard


А1. The combined device
е1. Signaling device of inclusion of indexes
left turn
е2. Signaling device of inclusion of indexes
right turn
е3. Signaling device of inclusion of indexes
tail light
е4. Alarm lamp of the index
fuel stock
е5. Control of a charge of the storage battery
е6. Control of wear of frictional slips
brake shoes
е7. Control of level of brake liquid and lay
brake system
е8. Illumination of a guard of devices
е9. Alarm lamp of seat belts
е11. Control of level of cooling liquid
е12. Control of level of oil
е13. Water level control in a screen wiper
е14. Control of failure of filament lamps
е15. Control of an inflatable safety cushion
е16. Control of a preliminary warming up
е17. Control of the antiblocking device of brake system (ABS)
е21. Indication of functioning of system of regulation of a proskalzyvaniye of driving wheels of rather basic surface (ASR)
е22. Control of system of regulation of a proskalzyvaniye of driving wheels of rather basic surface (ASR)
е24. Control of automatic blocked differential (ASO)
е25. Indication of functioning of automatic blocked differential (ASD)
е26. Control of operation of the CHECK ENGINE engine
е34. EDC control

1. Remove the dashboard.
2. If necessary remove cartridges of signaling devices on a reverse side by means of the left rotation and replace lamps. In Mercedes firm repair trucks for an otvorachivaniye of cartridges of lamps there is a special tool, but it can be executed also fingers or flat-nose pliers.
3. Replace a lamp only with a lamp having identical capacity and the same type.
4. Insert a cartridge of a lamp and wrap it to the right.
5. Mount the dashboard.



31. Screws
32. Holder
33. Pipe cover casing
S4х1. The Shtekkerny socket of the combined switch
S40х1. Shtekkerny socket темпомата
S4. The combined switch
S40. Switch темпомата

1. Remove a protective casing under a guard of devices.
2. Remove a steering wheel.

Observe precaution rules at the handling of the device of an inflatable safety cushion.

3. Unscrew screws from a contact spiral at directly established forward wheels so that it was possible to remove a contact spiral.


Do not unscrew completely screws, otherwise a contact spiral collapses and it will be necessary to establish it again in average situation.

4. Extend from the holder two shtekerny connections of a contact spiral and separate them. Remove a contact spiral.
5. Unscrew fixing screws to the combined switch.
6. Take the holder.
7. Take shtekkerny connection (S4x1) and a shift way бюгеля (shooter), deblock it.
8. Only at equipment tempomaty: Take and separate shtekkerny connection (S40x1).
9. Take a casing of a pipe cover (33) together with the combined switch, at need and the switch темпомата.


1. Get on a steering shaft the combined switch together with a pipe cover.
2. Get and screw the holder.
3. Lay connecting lines and fix tips of wires in return sequence.
4. Get a contact spiral on a steering shaft, thus lay a connecting wire. Pay attention that the contact spiral is got against the stop and that the groove on a contact spiral coincides with a fixing ledge on a steering shaft. Tighten hardly fixing screws. Connect tips of wires and fix them.
5. Establish a protective casing under a guard of devices.
6. Establish a steering wheel.