W202 Mercedes
+ 1.2. General information
+ 2. Maintenance
+ 3. Engines
+ 4. Greasing system
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. Ignition system
+ 8. Fuel system
+ 9. Transmission
+ 10. Running gear
+ 11. Steering
+ 12. Brake system
+ 13. Body
- 14. Electric equipment
14.1.2. Measuring devices
14.1.3. Equipment of measurements
14.1.4. Electric equipment checks
14.1.5. Sound signal
14.1.6. Replacements of safety locks
+ 14.1.7. Storage battery
+ 14.1.8. Generator
+ 14.1.9. Starter
14.1.10. Traction relay
+ 14.1.11. Lighting system
14.1.12. Devices
14.1.13. Dashboard
14.1.14. Filament lamps on the dashboard
14.1.15. Light switch
14.1.16. Radio receiver
+ 14.1.17. Aerial
14.1.18. Loudspeakers
- 14.1.19. Rubber brushes of screen wipers
14.1.19.1. Diagnostics of malfunctions of brushes of screen wipers
14.1.20. Jets of a stekloomyvatel
14.1.21. Washing nozzles of headlights
14.1.22. Screen wiper and its engine
14.1.23. Protect the car
14.1.24. Anticreeping "immunodeficiency"
14.1.25. Why headlights grow dull
14.1.26. "Galogenki"
+ 14.2. Electroschemes
|
It is necessary to replace rubber brushes of a screen wiper at bad quality of purification of glasses. In trade are offered as complete brushes of a screen wiper (a rubber brush with the holder), and separate rubber brushes of a screen wiper. If only the rubber brush is replaced, pay attention to that her holder was not bent.
|
|
The rubber brush is entered into two metal fixing directing (1) which at removal should understand separately. |
Removal
Prevention
At work on screen wipers Take the ignition key. When moving the lever of a brush or the lever mechanism of a screen wiper, since position "1" of the ignition key, automatic equipment of return of brushes can turn on in a starting position. I.e. the screen wiper works in a single mode until it is in a starting position. There is a danger of a trauma!
| PERFORMANCE ORDER |
| 1. Raise the lever of a brush of a screen wiper, without fixing it. |
|
2. Press down a plastic clip on a corrugated detail (1) and displace a screen wiper brush down (2) from a hook on the lever of a brush of a screen wiper. |
|
3. A narrow screw-driver (2) remove from the closed party back a rubber brush from both steel directing (2) and carefully extend a rubber brush from the directing. |
| 4. Unhook a rubber brush (3) from collars (4) on a screen wiper. |
|
Installation
| PERFORMANCE ORDER |
| 1. Freely lay a rubber brush not in fixing directing, and in screen wiper clips. |
|
2. Both directing the open profile party enter into a rubber brush so that flutes of the directing looked towards rubber and were fixed in groove ledges. The bend of the directing should look in the glass direction. |
| 3. Spring latches enter into a clamp flute if previously its forward end is mown by a file easier and is greased with soap water (detergent). |
| 4. Grease a rubber brush on the closed party with soap water that it slid in collars better. |
| 5. Both steel directing and a rubber brush clamp пассатижами and hang in collars of the screen wiper. |
6. Get a screen wiper brush so that it was between both directing pins on the screen wiper lever.
Prevention
If the new brush of a screen wiper is established, press down plastic clips on corrugated details.
|
| 7. Push a screen wiper brush in hooks of its lever, clamp plastic clips and by that fix a screen wiper brush. |
| 8. Press the lever of a brush of a screen wiper. Thus pay attention to that the rubber brush everywhere adjoined to glass. |
9. Include a screen wiper. The sector of cleaning should be cleared easily.
Prevention
The rubber sponge of a brush of a screen wiper at change of the direction of movement should be bent to (overturn). If it does not occur, carefully bend the lever of a brush of a screen wiper so that its end settled down parallel to glass.
|
|
|
|
