S-class W202 Mercedes

1993-2000 of release

Repair and car operation


W202 Mercedes
+ 1.2. General information
+ 2. Maintenance
+ 3. Engines
- 4. Greasing system
   4.2. Specification of engine oil
   4.3. Scope viscosity oils / class
   4.4. Consumption of oil
   4.5. Contour of circulation of oil (DD)
   4.6. Oil reduktsionny valve
   - 4.7. Oil pallet
      4.7.2. Diesel engine (2,0 l)
      4.7.3. Diesel engine (2,2/2,5 l)
   4.8. Indicator of level of oil
   4.9. The heat exchanger oil - / cooling liquid
   4.10. Diagnostics of malfunctions in a contour of circulation of oil
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. Ignition system
+ 8. Fuel system
+ 9. Transmission
+ 10. Running gear
+ 11. Steering
+ 12. Brake system
+ 13. Body
+ 14. Electric equipment
+ 14.2. Electroschemes


b47c026d b47c026d

4.7. Oil pallet

4.7.1. Petrol engine
GENERAL INFORMATION

 
1. Radiator clip
2. Clip of the case of the fan
3. Fan case
4. Radiator
5. Covering of electroconducting of the engine
11. Bolts of a forward support of the engine 		12. Bolts of a back support of the engine
16. Cover
S43. Shtekker of the sensor of level of oil
56. Oil pallet
56а. Sealing laying of the pallet

Bolts of fastening of the oil pallet

  
6. Bolt of M of 6 x 20 9 mm
7. Bolt of M of 6 x 35 9 mm
8. Bolt of M of 6 x 85 9 mm		 9. Bolt of M of 8 x 40 21 mm
10. Bolt of M of 10 x 40 40 mm
56. Oil pallet

Removal
PERFORMANCE ORDER
1. Remove the bottom cover of a motor compartment.
2. Remove the stabilizer.
3. Lower engine oil.
4. Uncover (16).
5. Remove clips (2).
6. Raise the case of the fan and put on the fan.
7. Disconnect clips (1) from a radiator.
8. Weaken the top oil pipeline (shooter) on the pump of the amplifier of a steering and turn down.
9. Remove a cable tape for engine electroconducting.
10. Remove a covering of electroconducting of the engine from a dividing partition between units.
11. Disconnect a forward exhaust pipe from a final collector.
12. Unscrew a support of the holder of an exhaust pipe from a transmission.
13. Disconnect the tip of the sensor of level of oil.
14. Unscrew bolts of a forward support of the engine.
15. Unscrew bolts of fastening of a back support of the engine.
16. Hook on the engine for lobbies and back eyes.
17. Raise the engine as much as possible horizontally.
18. Unscrew bolts of fastening (6/7/8/9/10) oil pallets and remove the oil pallet (56) (see fig. Bolts of fastening of the oil pallet).
19. Carefully clear a sealing surface of the oil pallet and a case of a cranked shaft.

Installation

PERFORMANCE ORDER
1. Establish the oil pallet with new sealing laying, level it rather back surface of a prileganiye to a check point and evenly manually fix bolts. Then alternately twirl bolts with the ordered moment (see fig. Bolts of fastening of the oil pallet).
Prevention

If the oil pallet is not leveled concerning a transmission, subsequently it will lead to noise.
2. Lower the engine.
3. Insert bolts of fastening of a forward support of the engine and screw up them manually.
4. Screw up bolts of a forward support of the engine with the moment of 40 N of m.
5. Put on the tip of the sensor of level of oil.
6. Attach a forward exhaust pipe to a final collector, a support of the holder of an exhaust pipe on a check point.
7. Establish a covering of electroconducting of the engine on a partition dividing units.
8. Fix engine electroconducting at the right wheel.
9. Turn an oil pipeline of the pump of the amplifier of a steering up and fix.
10. Put on clips a radiator.
11. Establish the case of the fan and fix clips.
12. Establish a cover (16).
13. Establish the stabilizer.
14. Establish the bottom cover of a motor compartment.
15. Fill in engine oil.
16. Warm up the engine and check tightness of the oil pallet.