S-class W202 Mercedes

1993-2000 of release

Repair and car operation



W202 Mercedes
+ 1.2. General information
+ 2. Maintenance
+ 3. Engines
- 4. Greasing system
   4.2. Specification of engine oil
   4.3. Scope viscosity oils / class
   4.4. Consumption of oil
   4.5. Contour of circulation of oil (DD)
   4.6. Oil reduktsionny valve
   - 4.7. Oil pallet
      4.7.2. Diesel engine (2,0 l)
      4.7.3. Diesel engine (2,2/2,5 l)
   4.8. Indicator of level of oil
   4.9. The heat exchanger oil - / cooling liquid
   4.10. Diagnostics of malfunctions in a contour of circulation of oil
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. Ignition system
+ 8. Fuel system
+ 9. Transmission
+ 10. Running gear
+ 11. Steering
+ 12. Brake system
+ 13. Body
+ 14. Electric equipment
+ 14.2. Electroschemes








b47c026d b47c026d


4.7.2. Diesel engine (2,0 l)

GENERAL INFORMATION

Diesel engine in volume of 2,0 l

 
3. Stopper of a masloslivny opening
6. Engine emphasis (type 201)
24. Engine shock-absorber (type 201)

Removal

PERFORMANCE ORDER
1. Remove the bottom cover of a motor compartment.
2. Remove the stabilizer of cross-section stability.
3. Disconnect the left longitudinal steering draft and the right shock-absorber of a steering.
4. Merge engine oil.
5. Disconnect a cable of weight of the battery (–).
Prevention

The anticreeping code of radio is thus erased.


6. Disconnect plusovy X4 wire from a connection place to the bottom party of the car at the left and пложите from above the engine.
7. Disconnect a casing of the fan and put from above the fan.
8. Unscrew the sensor of number of turns (L3).
9. Disconnect a weight wire between a starter and a body (shooter).
10. Remove a shchtekker of the sensor of level of oil.
11. Disassemble an intermediate steering soshka.
12. Automatic transmission: Separate oil pipelines in connecting details from маслошлангов, previously having clamped oil pipelines by means of shlangovy clips. Elements of connection close small plastic bags that dirt did not get into them.
13. Pick up the engine the corresponding cable or a chain for a forward eye (shooter) and raise the crane. If is not present at the disposal of the crane, insert into a cable suitable шта NSU, slightly raise the engine and обоприте on supports.
14. Unscrew from below from a longeron a bolt with an internal shestigrannik for the left forward support of the engine.
15. Unscrew from a longeron from below a bolt with an internal shestigrannik of the right forward support of the engine.
16. Raise the engine it is how possible above.
17. The oil pallet with a priflantsovanny lateral part: turn off a lateral part and remove together with sealing laying.
18. Unscrew bolts of fastening (19) oil pallets and remove the oil pallet (45) forward, depending on the movement direction. If necessary slightly turn a cranked shaft.
19. Remove sealing laying (45а), carefully clear sealing surfaces of the pallet and a case of a cranked shaft.

Installation

PERFORMANCE ORDER
1. Negative wire of the storage battery. Establish the oil pallet with new sealing laying, сориентировав its prileganiye to a back surface of a transmission, and evenly manually twirl fastening bolts. Then alternately screw up bolts with the next moments:
M of 6-10 N of m; M of 8-25 N of m; M of 10-40 N of m.
Prevention

In cars with an automatic transmission track, that the calibrated groove on an interface of the oil pallet entered into the unloading plug of the motor block.

2. If occurred removal: establish a lateral part of the oil pallet with new sealing laying and twirl with the moment of 10 N of m.
3. Lower the engine.
4. Establish bolts of fastening of a forward support of the engine and tighten with the moment of 30 N of m.
5. Automatic transmission: connect oil pipelines, remove shlangovy clips.
6. Establish an intermediate steering soshka.
7. Put on the tip of the sensor of level of oil.
8. Screw the sensor of number of turns.
9. Screw a "weight" cable between a starter and a body.
10. Establish and fix clips a fan casing.
11. Connect plusovy a cable (Х4).
12. Hang the left longitudinal steering draft and the right shock-absorber of a steering.
13. Establish the stabilizer.
14. Establish the bottom cover of a motor compartment.
15. Fill in engine oil.
16. Connect a wire of "weight" of the battery.
17. Expose hours
18. Set an anticreeping code of radio.
19. Warm up the engine and check tightness of the oil pallet.
20. Automatic transmission: check oil level.