W202 Mercedes
+ 1.2. General information
+ 2. Maintenance
+ 3. Engines
+ 4. Greasing system
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. Ignition system
- 8. Fuel system
- 8.1.1. Introduction
8.1.2. Fuel tank
8.1.3. Fuel level sensor
8.1.4. Fuel pump
8.1.5. Fuel filter
8.1.6. Air filter
8.1.7. Cross-section pipe of the air filter
8.1.8. Inlet gas pipeline
8.1.9. Cable gas / lever of a butterfly valve (DB)
8.1.10. Cable of management of gas (DB)
8.1.11. Contour of fuel of the diesel engine
8.1.12. Prestarting heating of diesel fuel
8.1.13. Fuel thermostat
8.1.14. Hydrovalve case
8.1.15. Cable gas / lever of a butterfly valve (DD)
8.1.16. Cable of management of gas (DD)
+ 8.2. System of injection of petrol engines
+ 8.3. System of injection and food of diesel engines
+ 8.4. System of production of exhaust gases
+ 9. Transmission
+ 10. Running gear
+ 11. Steering
+ 12. Brake system
+ 13. Body
+ 14. Electric equipment
+ 14.2. Electroschemes
|
Diesel engine in volume of 2,0 l
Diesel engine of 2,2/2,5 l
|
24. Accelerator pedal
31/1. The directing lever
32. Cable of management of gas
|
32/3. Adjusting bolt
38. Emphasis of the lever of a butterfly valve |
| PERFORMANCE ORDER |
|
Check on ease of a course and damage the adjusting lever, connecting draft and a cable of management of gas. Replace the damaged details. |
|
Adjustment on an idling mode (the pedal of an accelerator (224) is not pressed)
| PERFORMANCE ORDER |
| 1. Weaken a six-sided bolt (c) on connecting draft (200) hydrovalves. |
| 2. Weaken a nut (204/1) on a spherical head of connecting draft (204). |
3. Until then rotate an adjusting nut while the roller (215) in the kulisny lever without tension will lie down on a trailer emphasis.
Prevention
After adjustment between a plate of a spring (226) and the spring (227) should not be a gap.
|
| 4. Tighten a nut (204/1) on a spherical head of connecting draft. |
| 5. Automatic transmission: hang without a tension a spherical podpyatnik of a cable of management (211). For this purpose a cable of management pull to notable resistance. Rotate a bolt (211/1) until a hummock drive подвиснет without a tension. |
| 6. Directing lever (d) of the hydrovalve rotate until he will lie down on the idling limiter. |
| 7. Stretch connecting draft (200) on the riveted party until the free wheeling will be established. |
| 8. Tighten a bolt with a six-sided head (c). |
|
Regulation of full gas (mechanical transmission)
| PERFORMANCE ORDER |
| 1. Rotating to the left, uncouple an emphasis of the lever of a butterfly valve (216) in space for feet. Slowly squeeze out a pedal of an accelerator (224) until the control lever will directly reach an emphasis of the lever of a butterfly valve (shooter) on the pump of nozzles. |
| 2. In this situation, rotating to the right, fix an emphasis of the lever of a butterfly valve (216) in internal space. |
|
Regulation of full gas (automatic transmission)
| PERFORMANCE ORDER |
| 1. Squeeze out a pedal of an accelerator (224) against the stop without actuating of the switch of an accelerator (S16/7). |
| 2. Rotate the adjusting screw (232) until the control lever will directly reach an emphasis of a butterfly valve (shooter) on the fuel pump of nozzles. |
|
Regulation of a cable of management by gas
| PERFORMANCE ORDER |
|
Check on ease of a course and damage the adjusting lever and a cable of management of gas. The damaged details replace. |
|
Regulation in an idling mode (the pedal of an accelerator is not pressed)
| PERFORMANCE ORDER |
|
Rotate an adjusting bolt until the directing lever without tension will lie down on the limiter of a course (and). |
|
Regulation of complete opening of a butterfly valve (mechanical transmission)
| PERFORMANCE ORDER |
|
1. Rotating to the left, uncouple an emphasis of the lever of a butterfly valve (38) in space for feet and extend a persistent bolt a little. |
| 2. Slowly squeeze out an accelerator pedal until the directing lever directly will reach the emphasis of the lever of a butterfly valve (b) limiting its maximum opening. |
| 3. Rotating to the right, fix in this situation an emphasis of the lever of a butterfly valve in internal space. |
|
|
|
