S-class W202 Mercedes

1993-2000 of release

Repair and car operation



W202 Mercedes
+ 1.2. General information
+ 2. Maintenance
+ 3. Engines
+ 4. Greasing system
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. Ignition system
- 8. Fuel system
   - 8.1.1. Introduction
      8.1.2. Fuel tank
      8.1.3. Fuel level sensor
      8.1.4. Fuel pump
      8.1.5. Fuel filter
      8.1.6. Air filter
      8.1.7. Cross-section pipe of the air filter
      8.1.8. Inlet gas pipeline
      8.1.9. Cable gas / lever of a butterfly valve (DB)
      8.1.10. Cable of management of gas (DB)
      8.1.11. Contour of fuel of the diesel engine
      8.1.12. Prestarting heating of diesel fuel
      8.1.13. Fuel thermostat
      8.1.14. Hydrovalve case
      8.1.15. Cable gas / lever of a butterfly valve (DD)
      8.1.16. Cable of management of gas (DD)
   + 8.2. System of injection of petrol engines
   + 8.3. System of injection and food of diesel engines
   + 8.4. System of production of exhaust gases
+ 9. Transmission
+ 10. Running gear
+ 11. Steering
+ 12. Brake system
+ 13. Body
+ 14. Electric equipment
+ 14.2. Electroschemes








b47c026d b47c026d


8.1.16. Cable of management of gas (DD)

GENERAL INFORMATION

DIESEL ENGINE


Prevention

The cable is very sensitive to bends and consequently at installation demands the accurate address. The unique easy bend can lead to more its late breakage at car operation. Therefore cables which were earlier bent, it is not necessary to establish.


Removal

PERFORMANCE ORDER
1. Engine in volume of 2,0 l: unhook a cable of management of gas (230) on the adjusting lever (208). For this purpose squeeze out directing detail (240).
2. Engines in volume of 2,2/2,5 l: unhook a cable of management of gas on a spherical head of the directing lever.
3. Compress a plastic spring clip (228) and pull out a hummock drive from a support (225).
4. Dismantle a casing under the dashboard.
5. Unhook fastening of a hummock drive (shooter) on the lever of a pedal of an accelerator (223). For this purpose unhook a returnable spring (235) and extend the holder (233/2) together with a rasporny bolt.
6. Press from internal space of the car outside a cable of management of gas. Thus do not squeeze out the rubber plug.
7. Remove in a set a cable of management of gas.

Installation

PERFORMANCE ORDER
1. Grease a cable of management with gas between a directing element and a tip anticorrosive plastic greasing of the Mercedes-000 989 5110 type.
2. Instruction: at vehicles with an automatic transmission the cable of management of gas is established in its fastening together with a spring (shooter). Thanks to it the way of the lever of a pedal increases and opportunity of switching off of the switch of a pedal of an accelerator is given.
3. Check on damage or porosity the rubber plug (231), if necessary replace.
4. Stretch a cable of management of gas in internal space of the car and suspend on the accelerator lever. Pick up a returnable spring.
5. Mount a casing under the dashboard.
6. Enter a cable of management of gas through an opening in a support, press on a support and fix.
7. Engine in volume of 2,0 l: hang a cable of management of gas on the adjusting lever and fix it by means of a directing detail (240).
8. Engine in volume of 2,2/2,5 l: press a cable of management of gas on a spherical head of the directing lever.
9. Adjust a cable of management of gas.