S-class W202 Mercedes

1993-2000 of release

Repair and car operation



W202 Mercedes
+ 1.2. General information
+ 2. Maintenance
- 3. Engines
   3.1.2. Identification number
   + 3.1.3. Engine
   3.1.4. Cars with the conditioner
   3.1.5. Bottom cover of a motor compartment
   3.1.6. Covers of cast openings
   3.1.7. Natyazhitel of a chain
   + 3.1.8. Cover of a head of the block of cylinders
   + 3.1.9. Head of the block of cylinders
   + 3.1.10. Camshafts
   3.1.11. Hydraulic tarelchaty pushers
   3.1.12. Maslootrazhatelnye caps
   3.1.13. Valves
   3.1.14. Directing valves
   3.1.15. Saddles of valves in a head of the block of cylinders
   3.1.16. Compression
   - 3.1.17. Maple belt
      3.1.17.2. 6-cylinder engine
   3.1.18. Diagnostics of malfunctions (DB)
   3.1.19. General comments
   3.1.20. Repair work without engine dismantle
   + 3.1.21. Major maintenance of the engine
   + 3.2. Diesel engine (DD)
   3.2.3. Cars with the conditioner
   3.2.4. Bottom cover of a motor compartment
   3.2.5. Covers of cast openings
   3.2.6. Natyazhitel of a chain
   + 3.2.7. Camshaft
   + 3.2.8. Head of the block of cylinders
   + 3.2.9. Maslootrazhatelnye caps
   3.2.10. Cover of a head of the block of cylinders (2,2/2,5 l)
   3.2.11. Hydraulic tarelchaty pushers
   3.2.12. Valves
   3.2.13. Directing valves
   3.2.14. Saddles of valves in a head of the block of cylinders
   3.2.15. Head of the block of cylinders and motor block
   3.2.16. Compression
   3.2.17. Maple ridge belt
   3.2.18. Tense device of a maple ridge belt
   3.2.19. Diagnostics of malfunctions (DD)
+ 4. Greasing system
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. Ignition system
+ 8. Fuel system
+ 9. Transmission
+ 10. Running gear
+ 11. Steering
+ 12. Brake system
+ 13. Body
+ 14. Electric equipment
+ 14.2. Electroschemes








b47c026d b47c026d


3.1.17. Maple belt

3.1.17.1. 4-cylinder engine

GENERAL INFORMATION

1. Tense roller
2. Remenny pulley of a cranked shaft
3. The Remenny pulley of the cooling compressor (only with the conditioner)
4. Remenny pulley of the generator of a three-phase current
5. Remenny pulley of the pump of the amplifier of a steering
6. The Remenny pulley of the pump of cooling liquid
Lengths: 2040 mm and 2140 mm (with the conditioner)

1. Support
2. Tense sleeve
3. Tense roller
4. External bolt Е10

All additional units of the engine are put in action by means of a maple ridge belt. It is wider, than usual maple a belt, and has on inside many edges.

The automatic tense device provides a uniform tension of a maple ridge belt for an appreciable length of time.

The belt needs to be checked within regular maintenance on damages. Depending on the car equipment maple belts have various length.

Removal

PERFORMANCE ORDER
1. Remove the hydraulic coupling of the fan.
2. Get a natural a nozzle for bolt Е10 on tense roller and weaken a belt (11) turn clockwise.

Installation

PERFORMANCE ORDER
1. Check a profile of belt pulleys and tense device on absence of damages and pollution, in case of need clean or replace. Thus pay attention to the beaten-out installation sites of support of the device of a tension and a hole on belt pulleys.
2. Maple ridge belts with dirt adjournment between edges, cracks, a fringe and the broken edges surely replace.
3. Impose maple a belt, since a tense roller, according to digital designations in drawing.
4. Release tense roller (see drawing). Marking (In) should is only in working area (And). If it does not occur, or the belt has inappropriate length, or the tense device is faulty.
5. Visually check belt landing on belt pulleys.
6. Establish the hydraulic coupling of the fan.