S-class W202 Mercedes

1993-2000 of release

Repair and car operation

W202 Mercedes
+ 1.2. General information
+ 2. Maintenance
- 3. Engines
   3.1.2. Identification number
   + 3.1.3. Engine
   3.1.4. Cars with the conditioner
   3.1.5. Bottom cover of a motor compartment
   3.1.6. Covers of cast openings
   3.1.7. Natyazhitel of a chain
   + 3.1.8. Cover of a head of the block of cylinders
   + 3.1.9. Head of the block of cylinders
   + 3.1.10. Camshafts
   3.1.11. Hydraulic tarelchaty pushers
   3.1.12. Maslootrazhatelnye caps
   3.1.13. Valves
   3.1.14. Directing valves
   3.1.15. Saddles of valves in a head of the block of cylinders
   3.1.16. Compression
   + 3.1.17. Klinovy belt
   3.1.18. Diagnostics of malfunctions (DB)
   3.1.19. General comments
   3.1.20. Repair work without engine dismantle
   + 3.1.21. Major maintenance of the engine
   + 3.2. Diesel engine (DD)
   3.2.3. Cars with the conditioner
   3.2.4. Bottom cover of a motor compartment
   3.2.5. Covers of cast openings
   3.2.6. Natyazhitel of a chain
   + 3.2.7. Camshaft
   + 3.2.8. Head of the block of cylinders
   + 3.2.9. Maslootrazhatelnye caps
   3.2.10. Cover of a head of the block of cylinders (2,2/2,5 l)
   3.2.11. Hydraulic tarelchaty pushers
   3.2.12. Valves
   3.2.13. Directing valves
   3.2.14. Saddles of valves in a head of the block of cylinders
   3.2.15. Head of the block of cylinders and motor block
   3.2.16. Compression
   3.2.17. Maple ridge belt
   3.2.18. Tense device of a maple ridge belt
   3.2.19. Diagnostics of malfunctions (DD)
+ 4. Greasing system
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. Ignition system
+ 8. Fuel system
+ 9. Transmission
+ 10. Running gear
+ 11. Steering
+ 12. Brake system
+ 13. Body
+ 14. Electric equipment
+ 14.2. Electroschemes

3.2.4. Bottom cover of a motor compartment

GENERAL INFORMATION

Prevention

At removal and installation do not damage a surface of a protective material of a cover.

Removal

PERFORMANCE ORDER

1. Raise the car.
	2. Remove a forward covering (1), unscrew four bolts (arrow).
3. Remove a back covering (2), having unscrewed eight bolts of fastening. If there is a need, remove a lateral covering at the left and on the right, having turned off respectively two bolts of fastening of a lateral covering to a longeron and one bolt of fastening to the bottom support of the cross-section lever of an independent suspension bracket.

Installation

PERFORMANCE ORDER

1. After dismantle establish a lateral covering and fix bolts.
2. Establish a back covering and fix bolts.
	3. A forward covering establish so that the groove in front entered into a partition of a lateral part of a covering (3).
	4. Press a forward covering (1) up, thus the edge of a lateral part of a covering (3) should be from above coverings (1).
5. Tighten bolts of fastening of a forward covering.
6. Lower the car on the earth.