S-class W202 Mercedes

1993-2000 of release

Repair and car operation

W202 Mercedes
+ 1.2. General information
+ 2. Maintenance
- 3. Engines
   3.1.2. Identification number
   + 3.1.3. Engine
   3.1.4. Cars with the conditioner
   3.1.5. Bottom cover of a motor compartment
   3.1.6. Covers of cast openings
   3.1.7. Natyazhitel of a chain
   + 3.1.8. Cover of a head of the block of cylinders
   + 3.1.9. Head of the block of cylinders
   + 3.1.10. Camshafts
   3.1.11. Hydraulic tarelchaty pushers
   3.1.12. Maslootrazhatelnye caps
   3.1.13. Valves
   3.1.14. Directing valves
   3.1.15. Saddles of valves in a head of the block of cylinders
   3.1.16. Compression
   + 3.1.17. Klinovy belt
   3.1.18. Diagnostics of malfunctions (DB)
   3.1.19. General comments
   3.1.20. Repair work without engine dismantle
   + 3.1.21. Major maintenance of the engine
   + 3.2. Diesel engine (DD)
   3.2.3. Cars with the conditioner
   3.2.4. Bottom cover of a motor compartment
   3.2.5. Covers of cast openings
   3.2.6. Natyazhitel of a chain
   + 3.2.7. Camshaft
   + 3.2.8. Head of the block of cylinders
   + 3.2.9. Maslootrazhatelnye caps
   3.2.10. Cover of a head of the block of cylinders (2,2/2,5 l)
   3.2.11. Hydraulic tarelchaty pushers
   3.2.12. Valves
   3.2.13. Directing valves
   3.2.14. Saddles of valves in a head of the block of cylinders
   3.2.15. Head of the block of cylinders and motor block
   3.2.16. Compression
   3.2.17. Maple ridge belt
   3.2.18. Tense device of a maple ridge belt
   3.2.19. Diagnostics of malfunctions (DD)
+ 4. Greasing system
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. Ignition system
+ 8. Fuel system
+ 9. Transmission
+ 10. Running gear
+ 11. Steering
+ 12. Brake system
+ 13. Body
+ 14. Electric equipment
+ 14.2. Electroschemes

3.1.6. Covers of cast openings

GENERAL INFORMATION

6-CYLINDER ENGINE

Cast openings are located sideways the engine block. They are connected with channels of cooling liquid and closed by tin covers. If at low temperatures liquid freezes, the tin cover is squeezed out. So damage of the block of the engine is prevented. For cast openings it is necessary to replace not tight covers.

PERFORMANCE ORDER

1. Dismantle details of the unit which disturb access to the corresponding cover of cast openings.
2. Establish a screw-driver or a narrow chisel on the cover region.
	3. Carefully drive in inside a locking cover (121) on the one hand until it will not turn on 90 °.
	4. The turned cover extend by means of a trumpet key.
	5. Carefully clear a cast opening of deposits. The sealing surface (arrow) should be cleared of deposits.
6. Cover a sealing surface with hermetic (for example, Loctite N241 or Curil).
	7. Drive a new locking cover the suitable probe. Let's harden to hermetic according to the instruction of the manufacturer (about 45 minutes).
8. Establish the dismantled parts of the unit.
9. Fill in cooling liquid.
10. Warm up the engine, check level of cooling liquid and tightness of covers of cast openings.