S-class W202 Mercedes

1993-2000 of release

Repair and car operation



W202 Mercedes
+ 1.2. General information
+ 2. Maintenance
- 3. Engines
   3.1.2. Identification number
   + 3.1.3. Engine
   3.1.4. Cars with the conditioner
   3.1.5. Bottom cover of a motor compartment
   3.1.6. Covers of cast openings
   3.1.7. Natyazhitel of a chain
   + 3.1.8. Cover of a head of the block of cylinders
   + 3.1.9. Head of the block of cylinders
   + 3.1.10. Camshafts
   3.1.11. Hydraulic tarelchaty pushers
   3.1.12. Maslootrazhatelnye caps
   3.1.13. Valves
   3.1.14. Directing valves
   3.1.15. Saddles of valves in a head of the block of cylinders
   3.1.16. Compression
   + 3.1.17. Klinovy belt
   3.1.18. Diagnostics of malfunctions (DB)
   3.1.19. General comments
   3.1.20. Repair work without engine dismantle
   - 3.1.21. Major maintenance of the engine
      3.1.21.2. Alternatives
      3.1.21.3. Engine dismantle
      3.1.21.4. Sequence of dismantling
   + 3.2. Diesel engine (DD)
   3.2.3. Cars with the conditioner
   3.2.4. Bottom cover of a motor compartment
   3.2.5. Covers of cast openings
   3.2.6. Natyazhitel of a chain
   + 3.2.7. Camshaft
   + 3.2.8. Head of the block of cylinders
   + 3.2.9. Maslootrazhatelnye caps
   3.2.10. Cover of a head of the block of cylinders (2,2/2,5 l)
   3.2.11. Hydraulic tarelchaty pushers
   3.2.12. Valves
   3.2.13. Directing valves
   3.2.14. Saddles of valves in a head of the block of cylinders
   3.2.15. Head of the block of cylinders and motor block
   3.2.16. Compression
   3.2.17. Maple ridge belt
   3.2.18. Tense device of a maple ridge belt
   3.2.19. Diagnostics of malfunctions (DD)
+ 4. Greasing system
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. Ignition system
+ 8. Fuel system
+ 9. Transmission
+ 10. Running gear
+ 11. Steering
+ 12. Brake system
+ 13. Body
+ 14. Electric equipment
+ 14.2. Electroschemes


b47c026d b47c026d

3.1.21.4. Sequence of dismantling

GENERAL INFORMATION

It is most easier to assort the engine and to make all types of works at the figurative stand. Before engine installation it is necessary to shoot a flywheel with the stand with the coupling mechanism.

If the stand is not present, to assort the engine it is possible having strengthened it on a strong workbench or on a floor. When dismantling without the stand be very careful during manipulations with the engine.

If the engine is given in repair, at first it is necessary to remove all units to establish them subsequently precisely in the same order as well as at independent major maintenance. Such units treat:

 – generator and arms;
 – systems of decrease in toxicity of the fulfilled gases;
 – distributor of ignition, candle and high-voltage wires;
 – the thermostat with the case;
 – water pump;
 – carburetor;
 – inlet and final collectors;
 – oil filter;
 – fuel pump;
 – engine mount details;
 – a flywheel with the coupling mechanism.


Prevention

At removal from the engine of hinged units, with special attention treat those details which can be necessary at installation of the engine or for auxiliary installation. Put labels on laying, epiploons, pro-rates, shaft, washers, nuts, etc., to establish them in former situation.


If the block of cylinders of an incomplete complete set, i.e. the block of cylinders with established by the krivoshipno-shatunny mechanism and piston group is established, it is necessary to remove also a block head, the oil pallet and the oil pump. The list of details subject to removal is defined by the accepted option of repair.

If it is planned to carry out complete major maintenance, the engine it is necessary to disassemble and remove completely engine details in the following order:

 – covers of a gear belt of a cam-shaft;
 – gear belt;
 – cover of a head of the block of cylinders;
 – forward and back covers;
 – head of the block of cylinders and cam-shaft;
 – oil pallet;
 – oil pump;
 – shatunno-piston group;
 – cranked shaft.

Before dismantling and performance of procedures of major maintenance the following tools and the equipment will be necessary:

 – standard set of the tool;
 – small cash desks or plastic sacks for storage of details;
 – штапель for removal of the remains of laying;
 – development for a razzenkovka;
 – shock stripper;
 – micrometers;
 – the strelochny indicator with assembly system;
 – the adaptation for compression of springs;
 – the adaptation for a honningovaniye of cylinders;
 – the tool for cleaning of flutes of piston rings;
 – electrodrill;
 – set of taps and dies;
 – wire brushes;
 – solvent.