S-class W202 Mercedes

1993-2000 of release

Repair and car operation



W202 Mercedes
+ 1.2. General information
+ 2. Maintenance
+ 3. Engines
+ 4. Greasing system
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. Ignition system
+ 8. Fuel system
+ 9. Transmission
+ 10. Running gear
+ 11. Steering
+ 12. Brake system
- 13. Body
   13.2. Forward door
   13.3. Back door
   13.4. Handle of a forward door
   13.5. Handle of a back door
   13.6. Door lock
   13.7. Internal covering of doors
   13.8. Forward window regulator
   13.9. Glass of a forward window
   13.10. Back window regulator
   13.11. Glass of a forward door
   13.12. Window regulator engine
   13.13. Perchatochny boxing
   13.14. Sheeting of the handle of gear shifting
   13.15. Forward ashtray
   13.16. Average console
   13.17. Panel of service of heating
   13.18. Internal covering of the A-rack
   13.19. Internal covering of the S-rack
   13.20. Forward seat
   13.21. Back seat
   + 13.22. Central lock
   13.23. External mirror / glass of a mirror
   13.24. A covering under the dashboard
   13.25. Front bumper
   13.26. Rear bumper
   13.27. Internal wing of the car
   13.28. Car wing
   13.29. Lattice Mercedes radiator / emblem
   13.30. Draft of a cowl of the engine
   13.31. A covering under a windscreen
   13.32. The device of supply of air for salon heating
   13.33. Catchment basin
   13.34. Paint and varnish covering
   13.35. Metal corrosion
   13.36. Automake-up
   13.37. What creaks?
   13.38. Hatch
+ 14. Electric equipment
+ 14.2. Electroschemes








b47c026d b47c026d


13.2. Forward door

GENERAL INFORMATION

Door of the driver

1. Covering
2. Sealing laying
3. A-rack bolts
4. Protective sleeve
5. An aligning bolt

Removal

PERFORMANCE ORDER
1. Completely lower a window of a door of the driver.
2. Wring out a covering (1) and by means of the special tool turn to the right an internal tetrahedron disconnect blocking of tetrahedral shtekerny connection of a door.
3. Remove sealing laying.
4. Unscrew a bolt (13) door brakes (10). 14-a tetrahedron in a bolt head.
5. Note position of door hinges concerning a surface of their prileganiye, for example, lead round them a chertilka or откернуйте above and below. As a result adjustment of this door at installation is not required.
6. Unscrew four sharnirny bolts (3) and together with the assistant slightly disconnect a door from a door pillar.
7. Disconnect a protective sleeve (4) from a rack of a door and take shtekkerny connection (11).
8. Remove a door, trying not to damage a varnish covering.

Installation

PERFORMANCE ORDER
1. Insert shtekkerny connection (11) and close a stopper, having turned outside.
2. Fix spring clips a protective sleeve (4).
3. Establish a door and slightly fix fastening bolts.
4. So adjust the provision of a door that hinges coincided with the put marking.
5. Mount a covering (1).
6. Twirl with the moment of 25 N of m a bolt (13) fastenings of a door brake to a door pillar.
7. Attach a covering (1 and 2).
8. Adjust a door, twirl aligning bolt (5) with the moment of 25 N of m and bolts of hinges (3) with the moment of 35 N of m.

Adjustment

If the door is insufficiently driven after dismantling, it should be adjusted.

PERFORMANCE ORDER
1. Turn off a protective cover (7) door locks (8).
2. Adjustment is made by weakening of sharnirny bolts and door removing. Hinges have openings more than diameter of bolts, so the hinge can be moved.
3. For adjustment of the sizes of joints weaken sharnirny bolts (6) on a body, without unscrewing them. The size of a joint adjust door movement. So adjust a door that in relation to the details of a body located close the gap was parallel also identical size.
4. Door adjustment to a body contour: if the door in the closed condition insufficiently densely applies to a body, weaken sharnirny bolts (3) and (5) on a door and respectively move a door. The back door should enter at most on 1 mm in front inside further, than a forward door.
5. A protective cover of the door lock (7) screw up until then that it could be shifted in easy blows of a rubber hammer.
6. Adjust a protective cover of the door lock in the bottom area of a door. Close a door and level, as a result of it the provision of a protective cover of the door lock is leveled also. Then carefully open a door and tighten screws of a protective cover. Better to supervise moving, before weakening of screws outline a felt-tip pen the provision of a protective cover. Tighten screws of fastening of a protective cover of the lock with the moment of 30 N of m.
7. Check the correct prileganiye of sealing laying of a door to the car roof edge. If the door in a closed position is located faultlessly, tighten sharnirny bolts.