S-class W202 Mercedes

1993-2000 of release

Repair and car operation

W202 Mercedes
+ 1.2. General information
+ 2. Maintenance
+ 3. Engines
+ 4. Greasing system
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. Ignition system
+ 8. Fuel system
+ 9. Transmission
+ 10. Running gear
+ 11. Steering
+ 12. Brake system
- 13. Body
   13.2. Forward door
   13.3. Back door
   13.4. Handle of a forward door
   13.5. Handle of a back door
   13.6. Door lock
   13.7. Internal covering of doors
   13.8. Forward window regulator
   13.9. Glass of a forward window
   13.10. Back window regulator
   13.11. Glass of a forward door
   13.12. Window regulator engine
   13.13. Perchatochny boxing
   13.14. Sheeting of the handle of gear shifting
   13.15. Forward ashtray
   13.16. Average console
   13.17. Panel of service of heating
   13.18. Internal covering of the A-rack
   13.19. Internal covering of the S-rack
   13.20. Forward seat
   13.21. Back seat
   + 13.22. Central lock
   13.23. External mirror / glass of a mirror
   13.24. A covering under the dashboard
   13.25. Front bumper
   13.26. Rear bumper
   13.27. Internal wing of the car
   13.28. Car wing
   13.29. Lattice Mercedes radiator / emblem
   13.30. Draft of a cowl of the engine
   13.31. A covering under a windscreen
   13.32. The device of supply of air for salon heating
   13.33. Catchment basin
   13.34. Paint and varnish covering
   13.35. Metal corrosion
   13.36. Automake-up
   13.37. What creaks?
   13.38. Hatch
+ 14. Electric equipment
+ 14.2. Electroschemes

13.8. Forward window regulator

Removal

PERFORMANCE ORDER

1. Remove an internal covering of a door.
2. Carefully remove pressurizing film. Be careful: the film is easily torn.
	3. Glass of a window lower as it is possible below while the screw (2) will not appear in an assembly opening. (3–the window regulator tire, 1 – glass.)
4. Unscrew the screw (2) in front on the window regulator tire.
5. Slightly raise glass behind and Take crackers from the window regulator tire.
6. Press glass up and insure him from loss by a plastic or wooden wedge.
	7. Window regulator (4) приклепан. Drill 6 rivets (8) a drill 4, 8 mm. Thus track, that the drill did not enter into an internal tin of a door. For a zaklepyvaniye pincers are necessary for secret rivets.
8. Extend a window regulator with the tire and take down. An electric window regulator Take together with the engine. Disconnect a window regulator wire.

Installation

PERFORMANCE ORDER

1. Establish at a door a window regulator and rivet by means of pincers for secret клепки. If is not present at the disposal of pincers, it is possible to fix a window regulator screws and nuts. Screws before a twisting cover with a protective tool, for example, Loctite 270 or Omnifit.

2. Carefully lower glass and enter together with crackers from the window regulator lever into cut of the tire of a window regulator.

3. Insert the forward lever of a window regulator into the tire of the lift and screw, without tightening. The screw (2) is tightened only after the door window is adjusted.

4. Attach electric wires.

5. Adjust a door window.

6. Paste pressurizing film so that there were no folds.

Prevention

Do not damage a film – it should carry out sealing faultlessly.

7. Establish an internal covering of a door.