S-class W202 Mercedes

1993-2000 of release

Repair and car operation

W202 Mercedes
+ 1.2. General information
+ 2. Maintenance
+ 3. Engines
+ 4. Greasing system
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. Ignition system
+ 8. Fuel system
+ 9. Transmission
+ 10. Running gear
+ 11. Steering
+ 12. Brake system
- 13. Body
   13.2. Forward door
   13.3. Back door
   13.4. Handle of a forward door
   13.5. Handle of a back door
   13.6. Door lock
   13.7. Internal covering of doors
   13.8. Forward window regulator
   13.9. Glass of a forward window
   13.10. Back window regulator
   13.11. Glass of a forward door
   13.12. Window regulator engine
   13.13. Perchatochny boxing
   13.14. Sheeting of the handle of gear shifting
   13.15. Forward ashtray
   13.16. Average console
   13.17. Panel of service of heating
   13.18. Internal covering of the A-rack
   13.19. Internal covering of the S-rack
   13.20. Forward seat
   13.21. Back seat
   + 13.22. Central lock
   13.23. External mirror / glass of a mirror
   13.24. A covering under the dashboard
   13.25. Front bumper
   13.26. Rear bumper
   13.27. Internal wing of the car
   13.28. Car wing
   13.29. Lattice Mercedes radiator / emblem
   13.30. Draft of a cowl of the engine
   13.31. A covering under a windscreen
   13.32. The device of supply of air for salon heating
   13.33. Catchment basin
   13.34. Paint and varnish covering
   13.35. Metal corrosion
   13.36. Automake-up
   13.37. What creaks?
   13.38. Hatch
+ 14. Electric equipment
+ 14.2. Electroschemes

13.7. Internal covering of doors

GENERAL INFORMATION

Door of the driver


1. Window regulator handle 2. Lock socket 3. Deepening for the handle 4. Covering	5. Internal covering of a door Instruction: on back doors it is necessary to carry out work as appropriate

Removal

PERFORMANCE ORDER

1. Unscrew the lock (2) socket a screw-driver and remove it.
2. Completely lower door glass by means of the handle.
	3. Remove the window regulator handle for what a small screw-driver press a lock hook on a covering. Lower a covering down in the direction of an arrow and remove.
4. Remove the handle from an axis, remove a rasporny washer.
5. Blenda (3) for door actuating from within disconnect fingers or a screw-driver from an internal covering of a door and remove.
	6. Unscrew the screw (6) on the mechanism of management of a door from within.
7. Wring out a covering (4) under an armrest in a door pocket and unscrew the screw with a crosswise shliyets on a head.
8. An internal covering of a door krugoobrazno slightly disconnect from a door tin.
9. A covering of a door wring out from a door tin from the bottom party and sideways a wide shpatel or a screw-driver, thus disconnect spring clips. To begin with the bottom party of a covering. Prevention Lay a material not to scratch a varnish.
	10. Open a stopper (7) mechanisms of actuating of a door from within and disconnect the mechanism (8). At "electricly an adjustable seat of the driver" instead of the mechanism flexible draft is built in, disconnect it.
11. Disconnect the wire tip from a door covering.
12. Pull an internal door covering up over the button of blocking of a door and take from a door tin.

Installation

PERFORMANCE ORDER

1. Before assembly track the correct installation of a pressurizing film. Small damages of a film stick with a sticky tape, at big cracks replace a film. Prevention At plant the holder of fastening of an armrest приклепывается only after film installation. At replacement of a film cut out this area and stick a vnakhlestka or condense with a gluing tape.
2. Put on the wire socket.
3. Insert the mechanism of actuating of a door from within and fix it.
	4. Replace the damaged spring clips. Establish an internal covering from above over the button of blocking of a door, enter into the tire for a sealant and at the same time with spring clips in openings in a door tin.
5. Press fists an internal covering of a door in the field of spring clips.
6. Twist the screw with a crosswise shliyets below an armrest. Impose a covering.
7. Fasten management of a door from within two screws. Impose a handle cover.
	8. A washer of a gap (3) handles of a window regulator establish in big diameter to a door covering.
9. Get the handle on an axis. At an open window the handle should be directed obliquely forward up.
10. Pull from below a cover (1) over the handle (2), thus track, that the head of a cover entered into a flute on a handle axis. Advance a covering forward so, fixing hooks (shooter) will not enter yet into gearing.
11. Raise glass up by means of the handle.
12. Insert a covering for the door lock from above and from below fix the screw.