S-class W202 Mercedes

1993-2000 of release

Repair and car operation

W202 Mercedes
+ 1.2. General information
+ 2. Maintenance
+ 3. Engines
+ 4. Greasing system
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. Ignition system
+ 8. Fuel system
+ 9. Transmission
+ 10. Running gear
+ 11. Steering
+ 12. Brake system
- 13. Body
   13.2. Forward door
   13.3. Back door
   13.4. Handle of a forward door
   13.5. Handle of a back door
   13.6. Door lock
   13.7. Internal covering of doors
   13.8. Forward window regulator
   13.9. Glass of a forward window
   13.10. Back window regulator
   13.11. Glass of a forward door
   13.12. Window regulator engine
   13.13. Perchatochny boxing
   13.14. Sheeting of the handle of gear shifting
   13.15. Forward ashtray
   13.16. Average console
   13.17. Panel of service of heating
   13.18. Internal covering of the A-rack
   13.19. Internal covering of the S-rack
   13.20. Forward seat
   13.21. Back seat
   + 13.22. Central lock
   13.23. External mirror / glass of a mirror
   13.24. A covering under the dashboard
   13.25. Front bumper
   13.26. Rear bumper
   13.27. Internal wing of the car
   13.28. Car wing
   13.29. Lattice Mercedes radiator / emblem
   13.30. Draft of a cowl of the engine
   13.31. A covering under a windscreen
   13.32. The device of supply of air for salon heating
   13.33. Catchment basin
   13.34. Paint and varnish covering
   13.35. Metal corrosion
   13.36. Automake-up
   13.37. What creaks?
   13.38. Hatch
+ 14. Electric equipment
+ 14.2. Electroschemes

b47c026d b47c026d

13.4. Handle of a forward door


1. Door handle
2. Directing the lock cylinder
3. Rotary core
4. Laying
5. Laying
6. A bolt with internal shestigranniky 4 mm
7. A holding bracket for a bolt
8. Basic bracket
9. Screws


1. Get a door sealant at height of the door lock of a groove of a door.
2. Turn off approximately on 4 turns a bolt with an internal shestigrannik (6) by means of 4 mm of a face key through an opening at doors. The bolt with an internal shestigrannik is insured against drop-out by the holder (7).
3. Directing (2) extend at first back, and then outside.
4. Extend the door handle (1) with laying (4) back from a basic bracket and remove. The basic bracket can be removed, in case of need, from the interior of a door, but for this purpose it is necessary to remove a door covering.
5. Remove laying (5).


Door lock

2–directing the lock cylinder
3–rotary core
10-ekstsentrikovy adjusting screw
11-door lock
12-the operating lever

11-door lock
13-an opening under the ekstsentrikovy adjusting screw
14-an opening under the screw with an internal shestigrannik

1. Establish the ekstsentrikovy regulating screw (10) outside thanks to what the door handle is easier mounted.
2. Establish the door handle with laying and thus enter into the operating lever (12) of the door lock.
3. Behind insert directing the cylinder of the lock (2) and also enter a rotary core (3) into management of the door lock.
4. Fix the door lock a bolt with an internal shestigrannik.
5. Adjust by means of the ekstsentrikovy screw (10) a gap between the handle (1) and operating lever (12) a crosswise screw-driver through an opening (13) on the forward party of a door. The gap should make from 1 to 3 mm.
6. Insert a sealant of a door and check door work.