S-class W202 Mercedes

1993-2000 of release

Repair and car operation

W202 Mercedes
+ 1.2. General information
+ 2. Maintenance
- 3. Engines
   3.1.2. Identification number
   + 3.1.3. Engine
   3.1.4. Cars with the conditioner
   3.1.5. Bottom cover of a motor compartment
   3.1.6. Covers of cast openings
   3.1.7. Natyazhitel of a chain
   + 3.1.8. Cover of a head of the block of cylinders
   + 3.1.9. Head of the block of cylinders
   - 3.1.10. Camshafts
      3.1.10.1.2. Control / adjustment of a basic provision
      3.1.10.2. 6-cylinder engine
   3.1.11. Hydraulic tarelchaty pushers
   3.1.12. Maslootrazhatelnye caps
   3.1.13. Valves
   3.1.14. Directing valves
   3.1.15. Saddles of valves in a head of the block of cylinders
   3.1.16. Compression
   + 3.1.17. Klinovy belt
   3.1.18. Diagnostics of malfunctions (DB)
   3.1.19. General comments
   3.1.20. Repair work without engine dismantle
   + 3.1.21. Major maintenance of the engine
   + 3.2. Diesel engine (DD)
   3.2.3. Cars with the conditioner
   3.2.4. Bottom cover of a motor compartment
   3.2.5. Covers of cast openings
   3.2.6. Natyazhitel of a chain
   + 3.2.7. Camshaft
   + 3.2.8. Head of the block of cylinders
   + 3.2.9. Maslootrazhatelnye caps
   3.2.10. Cover of a head of the block of cylinders (2,2/2,5 l)
   3.2.11. Hydraulic tarelchaty pushers
   3.2.12. Valves
   3.2.13. Directing valves
   3.2.14. Saddles of valves in a head of the block of cylinders
   3.2.15. Head of the block of cylinders and motor block
   3.2.16. Compression
   3.2.17. Maple ridge belt
   3.2.18. Tense device of a maple ridge belt
   3.2.19. Diagnostics of malfunctions (DD)
+ 4. Greasing system
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. Ignition system
+ 8. Fuel system
+ 9. Transmission
+ 10. Running gear
+ 11. Steering
+ 12. Brake system
+ 13. Body
+ 14. Electric equipment
+ 14.2. Electroschemes

3.1.10.2. 6-cylinder engine

GENERAL INFORMATION

Prevention

If details of management are used by valves again, it is necessary to establish them on the same places. Not to mix a detail, we recommend to make the panel for their storage. Camshafts are dismantled up at the established head of the block of cylinders.

Removal

PERFORMANCE ORDER

1. Disconnect a "weight" wire (–) batteries. Prevention The anticreeping code of radio is thus erased.
2. Weaken maple a ridge belt.
3. Uncover heads of the block of cylinders.
4. Remove a forward casing.
5. Establish the cylinder 1 in VMT.
6. Note the provision of an operating chain concerning each of two chain wheels of camshafts. For this purpose put with paint a stroke on a chain and a chain wheel.
7. Unscrew and remove a gear wheel of an inlet camshaft.
8. Remove an operating chain from a gear wheel of an inlet camshaft.
	9. Check, whether there are camshafts in a basic provision. Adjusting openings in diameter of 4 mm at a basic provision of camshafts are placed respectively outside of the upper edge of a head of the block of cylinders (arrow). The regulator of camshafts costs in the spat direction (late).
Prevention Camshafts remove and establish only in a basic provision. They are very sensitive to a break and consequently should be mounted, whenever possible, without tension.
	10. Unscrew covers of bearings of camshafts 1 and 8. Remove covers of bearings.
Prevention Bolts of covers of bearings at first weaken cross-wise on 1/2 turns, then on one turn weaken all bolts and after unscrew.
11. For dismantling of an inlet camshaft at first remove covers of bearings 9, 12 and 14.
12. Then remove covers of bearings 10, 12 and 13. Thus weaken bolts alternately and slowly, counteraction will not be removed yet.
13. For dismantling of a final camshaft at first remove covers of bearings 4, 5 and 7.
14. At the end remove covers of bearings 2, 3 and 6. And weaken bolts slowly and alternately, counteraction will not be removed yet.
15. Take camshafts.

Installation

PERFORMANCE ORDER

1. All assembly details carefully clean flushing gasoline, clear sealing surfaces.

2. Check tarelchaty pushers.

3. Camshafts and places of support grease with engine oil.

Prevention

At replacement of camshafts watch correctness of their identification. The identifier of camshafts is on installation sites of bearings 3 and 10 behind a bearing cover. The letters following the identifier, represent only designation of technological operation.

4. Establish an inlet camshaft so that the sharp ends of cams in the middle of the third cylinder were directed down.

5. At first mount covers of bearings 10, 11 and 13. Thus tighten bolts cross-wise alternately, respectively, on one turn.

6. Then mount covers of bearings 9, 12 and 14.

7. Impose an operating chain on a gear wheel of an inlet camshaft.

8. Insert into a management chain a gear wheel of an inlet camshaft and fix a new bolt with a fillet with the moment of 20 N of m. Then tighten a bolt a rozhkovy key on 90 °.

9. Check coincidence of the marking put at dismantle on gear wheels of camshafts and an operating chain.

10. Establish a cover of a head of the block of cylinders.

11. Expose time on hours.

12. Set an anticreeping code of radio.